|
|
|
|
|
|
|
|
|
|
bdsva medical school freshman
Joined: 28 Jul 2009 Posts: 11 Location: virginia beach va |
Posted: Mon Aug 10, 2009 3:22 pm Post subject: kip 8000 15" |
|
|
Hello folks,
We are trying to register 15" media on our 8000 and cant get it to recognize it as 15 only 11, 12 17 18 or 22...
any ideas? |
|
|
|
|
|
|
|
|
|
|
Desertdog resident
Joined: 06 Dec 2004 Posts: 162 Location: Hinges of Hell |
Posted: Mon Aug 10, 2009 4:49 pm Post subject: |
|
|
I beleive you need to switch format from arch to eng _________________ "Learn how to work, Kid" - BTLS |
|
|
|
|
|
|
|
|
|
|
bdsva medical school freshman
Joined: 28 Jul 2009 Posts: 11 Location: virginia beach va |
Posted: Mon Aug 10, 2009 4:53 pm Post subject: |
|
|
we have done both.... |
|
|
|
|
|
|
|
|
|
|
james resident
Joined: 10 Dec 2005 Posts: 249 Location: So Calif |
Posted: Mon Aug 10, 2009 5:55 pm Post subject: |
|
|
Are you using the bypass tray?
Our 8000 paper draws don't have sensors for 15" paper. Our spindels don't show a 15" mark to line up the paper roll to either.
We have never used 15" rolls. Not sure if the bypass will recognize 15". |
|
|
|
|
|
|
|
|
|
|
bdsva medical school freshman
Joined: 28 Jul 2009 Posts: 11 Location: virginia beach va |
Posted: Mon Aug 10, 2009 5:58 pm Post subject: |
|
|
we are using the rolls. half size of a 30 x 42... |
|
|
|
|
|
|
|
|
|
|
tech2tech doctor
Joined: 04 Mar 2005 Posts: 377
|
Posted: Wed Aug 12, 2009 10:50 pm Post subject: |
|
|
You need to set it to 17" and when you submit the job set it to centered so it will only print in the 15" area |
|
|
|
|
|
|
|
|
|
|
gri_addison dreaming of medical school
Joined: 06 Nov 2009 Posts: 1 Location: Addison, TX |
Posted: Fri Nov 06, 2009 3:37 pm Post subject: |
|
|
Did anyone get this to work? We tried every combination we could think of to get our 8000 to recognize the paper, but it always goes back to 11" and 12".
Any help or suggestions is apreciated. |
|
|
|
|
|
|
|
|
|
|
Jammin intern
Joined: 04 Sep 2007 Posts: 121 Location: Colorado |
Posted: Mon Nov 09, 2009 3:40 pm Post subject: |
|
|
This is what we do.
1.You can only use drawer 1
2.align the right side of your roll where it says A3 on spindle.KIP should say 18"
3.In KIP Request force size and tell it is an 18" roll and 21" long.
then shift the image all the way to the left (still in force size) save it as something you will remember.
and away you go priniting 15x21 on the 8000 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|